Mitsubishi service engine soon, also known as check engine light, comes on when the On-Board Diagnostic (OBD) system detects a problem with the engine, emission system or transmission.
If your Mitsubishi check engine light stays on, first check that the gas cap is on tight. If that is not the problem, read the fault codes by connecting an OBD2 scanner to the diagnostic port located under the dashboard. See the instructions below.
On some Mitsubishi models, check engine light may come on instead of the service engine soon. Both these lights serve the same functions.
Check engine light and the service engine soon should not be confused with Routine maintenance required message which is meant to remind the driver of regular maintenance.
What you notice when your Mitsubishi service engine soon light comes on:
- Mitsubishi runs rough
- Engine misfire or juddering
- Lack of power
- Poor throttle response
- Unusual sound from the engine
- Smoke from the exhaust
- Engine idles to high
- Engine dies soon after it starts
These symptoms indicate that the engine in your car is not working as it should.
If your Mitsubishi service engine soon light is on, but the car runs and drives fine the problem could be due to evaporative leak in the fuel system or a loose gas cap.
Most likely problems to trigger Mitsubishis check engine or service engine soon light:
- Faulty oxygen sensor
- Dirty mass airflow sensor
- Worn spark plugs
- Bad ignition coil
- Loose gas cap
- Vacuum leak
- Clogged catalytic converter
There are hundreds of possible issues that can turn on the check engine light on a Mitsubishi vehicle. To find out why the light is on, read the fault codes with an OBD-II scanner.
How to Diagnose Mitsubishi Check Engine Light
When the check engine light comes on a trouble code would be set on the computer. Use an OBD-II scanner to read the codes via the diagnostic port located under the dashboard on the driver's side. All 1996 and later Mitsubishi vehicles are equipped with the OBD-II diagnostic system.
- Plug OBD-II scanner into the diagnostic port under the dashboard.
- Turn on the ignition but don't turn on the engine.
- Turn on the scanner and select Read Fault Codes.
- Write down all codes and research each code online to better understand what can cause each code.
Once the repair has been made, the trouble code can be erased. Most OBD2 scanners and all scan tools are able to do this with the press of a button.
Check Engine Light Flashing
If your Mitsubishi check engine light is flashing, avoid driving for an extended time as doing so will cause damage to the catalytic converter and even may lead to the engine overheating.
Flashing service engine soon light means that there is an engine misfire which in most cases is caused by a faulty spark plug or ignition coil.
Here is a list of the common problems that trigger the Mitsubishi service engine light to come on.
Old spark plugs will cause your Mitsubishi check engine light to come on with fault codes P0300, P0301, P0302, P0303, P0304.
Also, they can cause your vehicle to have reduced power and a decrease in fuel economy. Keep in mind that driving with bad spark plugs you may damage your catalytic converter and oxygen sensors.
Faulty spark plugs are a common problem that triggers the check engine light on Mitsubishi cars. The problem is generally not the manufacturer's fault but a lack of maintenance on the owner's part. Spark plugs are maintenance items and need to be replaced as the car nears 100 000 mile mark. Check your owner's manual for the recommended spark plug replacement interval.
Mass Air Flow Sensor
The engine in your Mitsubishi has, in most cases, an integrated MAF and intake air temperature sensors. With time, it can get contaminated with dirt, giving false readings. This will result in rough idle, lack of power or hesitation on accelerations. Cleaning the sensor is quite simple, but only use MAF cleaner fluid for this job.
Another possibility is an intake leak. Codes: P0102 (Mass airflow sensor), P0113 (Intake air temperature sensor)
Coolant Temperature Sensor
Some Mitsubishis are somewhat more prone to coolant temperature sensor issues. A faulty CTS will give false temperature reading, causing in most cases engine running rich. Also, it will show the incorrect and misleading temperature reading on your dashboard. In addition to the sensor itself, make sure the wiring is not damaged. Code: P0115 (Coolant temperature sensor malfunction)
All turbocharged engines, and especially diesel ones, can suffer from under-boost. This is a situation where the desired boost pressure is not reached. It can be caused by a massive intake leak or a crack at vacuum hoses that regulate the turbo. Another possibility is an excessive carbon build-up inside the intake manifold.
This problem may trigger fault code P0299 (Boost pressure regulation control range not reached).
A small leak with the EVAP system is a widespread problem.
The first thing to check is if the fuel tank cap is loose. Other possibilities are cracks in EVAP hoses or vapor canister or a faulty purge or canister vent valves. The best way to find a fault is to test the whole system with a smoke generator machine.
This problem may trigger fault code P0456 (Evaporative Emissions System - Small leak detected)
A check engine light caused by an emission control related issues is something that you are likely to encounter if you drive a higher-mileage Mitsubishi.
Although this will be signaled as a catalytic converter low efficiency, it is easily possible that you have a faulty downstream O2 sensor. Make sure to rule this out before changing a much more expensive catalytic converter.
This problem may trigger fault codes P0420 to P0431 (Catalyst Efficiency Below Threshold).
Transmission issues in cars that are equipped with a CVT gearbox are usually caused by a faulty transmission fluid pressure switch, which controls the torque converter solenoid operation. As this switch is installed on the outer side of the gearbox, it is easily replaced.
This problem may trigger fault code P0842 (transmission fluid pressure switch circuit low).
DPF (Diesel models)
Most 2007 or newer Mitsubishis with diesel engines have a Diesel Particulate Filter or DPF. This is a device that traps the soot from the exhaust. It can get clogged over time, resulting in high temperatures and excessive back-pressure. In most cases, the build-up can be burned-off by triggering a regeneration process.
This problem may trigger fault code: P1499 (DPF temperature abnormally high).
Can a Loose Gas Cap Trigger Check Engine Light?
If your Mitsubishi check engine light came on after fueling, there is a good chance that you have a loose gas cap or poor fuel quality.
A loose or missing fuel cap on a Mitsubishi can trigger the check engine light to come on because it makes the On-Board Diagnostic system think there is a problem with the fuel system.
Tighten the gas cap or replace it but don't expect the check engine light to reset immediately. It may take two to four days for the check engine light to reset on its own.
If your Mitsubishi check engine light stays on, first check that the gas cap is on tight. Tighten the gas cap. If no other codes are present, the check engine light will reset within two to three days of normal driving.
If the check engine or service engine soon lights stay on, read the fault codes by connecting an OBD2 scanner into the diagnostic port located under the dashboard.
Always research the code and possible causes. Don't replace parts based on the fault code alone. Get a second opinion from a mechanic if necessary.
If you are the original owner and your Mitsubishi is less than 10 years old and has less than 100 000 miles your car may still be under warranty. A Mitsubishi dealer should diagnose and fix your problem-free of charge.
This guide applies to all 1996 and newer Mitsubishi vehicles including Lancer, Montero, Outlander, Galant, Eclipse, Raider, Pajero, Mirage, etc.