Porsche Timing Chain Tensioner Replacement

Over time Porsche timing chain tensioners may weaken, causing a rattle for about 5 seconds at startup.

One of the most common issues that cause Porsche engine noise for about 5 to 10 seconds on startup is a weak timing chain tensioner that is not maintaining hydraulic pressure when the engine is turned off and parked for an extended time.

Symptoms

  • Engine rattle noise at startup
  • Excessive timing chain slack
  • Check engine light on
  • Engine runs rough
  • Engine won't stay running

Warning

  • Record the timing marks before you start work.
  • Replace one tensioner at a time.
  • Verify timing marks before starting the engine.
  • After you replace each tensioner crank the engine by hand two full revolutions before you start it.

What you will need

  • Porsche Timing Chain Tensioner
    • Porsches typically have three tensioners. One near the air conditioner compressor (bank 1-3), one by the crankshaft (IMS chain tensioner or also known timing chain tensioner for intermediate shaft) and one on the left bottom corner of the engine (bank 4-6).
  • Ratchet wrench
  • 27mm socket
  • Screwdriver,
  • Torx Sockets,
  • E Torx Sockets
  • Torque Wrench

Procedure

In this guide, we go over the instructions on how to change Porsche left lower timing chain tensioner with the engine in the car.

Pictures in this guide are from a Porsche Cayenne with V8 engine, but the procedure should help you change the tensioners on other Porsche models as well.

  1. Park your Porsche on a level surface and allow the engine to cool down.getting ready to replace porsche timing chain tensioner
  2. Jack up the vehicle and remove the lower engine covers. On top of the engine remove the plastic trims and if needed the intake air hose to access the front of the engine.access porsche timing chain tensioner
  3. Place a socket on the crankshaft pulley and rotate the crankshaft to bring it to TDC. Use Porsche timing tool or an 8mm Allen wrench to lock the crank pulley to the block.turn porsche crankshaft by hand
  4. Lock the crankshaft (and when required the camshafts) in position. It is crucial to lock the crankshaft to prevent the timing chain from jumping when the tensioner is removed. Also we recommend locking the camshaft as well. To lock the camshaft, you need to remove the green cam seals on each cam cover.
  5. Locate the tensioners. Porsches have up to three tensioneers. IMS chain tensioneer and bank 4-6 tensioner can be replaced with the engine in the car. Bank 1-3 tensioner may require accessories to be removed access it.porsche cayenne timing chain tensioner
  6. Use a 27mm socket and ratchet to break loose the tensioner. Note that the tensioner has lots of thread; therefore, it will take a lot of turning to remove it. Replace one tensioner at a time.porsche cayenne timing chain tensioner replacement
  7. Prime the new tensioner. Soak the new tensioner in engine oil while it is soaked in oil pump it a few times to prime it.
  8. Install the new tensioner.
  9. Replace next tensioner.
  10. Don't start the engine yet. Remove the locking pins. Turn the engine by hand two full revolutions to make sure there is no intereference.
  11. Next check, the timing marks are lining up correctly. This will allow you to make sure the timing didn't jump.

Always replace one tensioner at a time. Check your work by turning the engine by hand two full revolutions.

In some cases, a rattle noise is present when the vehicle is parked for several weeks or months. This is normal unlesss you experience engine noise on start up when the vehicle is parked overnight.

It is recommended to get your car diagnosed by a professional Porsche mechanic to confirm the tensioners are the culprit.

Another common problem on Porsche vehciles is IMS bearing failing and is often misdiagnosed as a bad timing chain tensionner.

Porsche