How to Program Audi Garage Door Remote HomeLink

In this guide, you will find instructions on how to program Audi garage buttons.

In fact, Audi allows you to use buttons in the car to open and close your garage door, automatic gate, security systems or even home lighting.

Audi Grage Door Programming via MMI

program garage door programming
  1. Press the CAR button on the center console.
  2. Go to Car Systems
  3. Go to Vehicle Settings
  4. Go to Garage Door Opener
  5. Select Program Door Opener
  6. Press the button on the roof that you want to program. The LED light next to the buttons turns on.
  7. Go to the front of your Audi and hold your existing garage door opener in front of the Audi logo.
  8. Press and hold the button of your remote control for 30 seconds.
  9. Your Audi hazard lights blink three times it means programming was carried out successfully. If the turn signals blink only once repeat the procedure. All the steps need to be completed within 5 minutes.

*If you have no working garage remotes for your garage door, complete steps 1 through 6 then go to your garage door motor press the LEARN button.

How to Program Audi Garage Door Buttons

audi home link garage door opener programing
  1. Park your Audi close to the garage. Do not park the car where it can be hit by the garage door or an automatic gate.
  2. Turn on the ignition. If your Audi has START button, press it without pressing on the brake pedal. All dash lights will be on but do not start the engine.
  3. Press and hold the button that you want to program for 10 seconds. This is the button by the dome light in your car, not the remote garage door opener.
  4. Go to the front of your Audi and hold your existing garage door opener in front of the Audi logo.
  5. Press and hold the button of your remote control for 30 seconds.
  6. Your Audi hazard lights blink three times it means programming was carried out successfully. If the turn signals blink only once repeat the procedure. All the steps need to be completed within 5 minutes.

How to erase Audi Garage Door Opener Memory

CLEAR AUDI GARAGE DOOR REMOTE

A time will come that you will need to delete the garage door remotes from memory, or in other words unsynchronise them.

For example, if you decide to sell your Audi, remember to clear the memory for the garage door opener.

  1. Press CAR button on the MMI controls
  2. Go to CAR SYSTEMS
  3. Vehicle Settings
  4. Garage Door Opener
  5. Clear Program Settings
  6. YES

Option 2: Manually clear Audi garage door opener

  1. Press and hold both outer buttons in the headliner for at least 20 seconds.
  2. Once the small LED light turns off, the button settings have been cleared.

These instructions will help owners of Audi A1 A3 A4 A5 A6 A7 Q3 Q5 Q7 TT learn how to program a garage remote.

Audi
Visitor

Adding a few more pointers here. You might notice a few things if you are doing this yourself e.g.

1. If the LED is continuously on (not blinking, just keeps on) - This indicates that you did everything correctly, programming has been accepted and you are good to go

2. If the LED blinks twice and then remains on without any blinking - This would indicate that the Audi require some additional input

  • Log in or register to post comments
  • Visitor

    This does not apply to the 2019 Q3. There is no button on the roof, only a touchpad interface. Following the MMI instructions also does not work. Do you have instructions for this car?

  • Log in or register to post comments
  • Visitor

    THESE INSTRUCTIONS DID NOT WORK FOR ME AS THE REMOTE was unable to link up with the Q5. It seems to need a special remote as it will not sync directly with garage door unit. That is not the least bit convenient. Audi should do better than that. Why must I go purchase a special remote for the 2019 Q5?

  • Log in or register to post comments